Summary:
I found it very confusing that running infer with --debug makes the
report to be different.
Intuitively, I expect (and I think majority of users would expect) that
`--debug` makes things more verbose (and potentially more slow / consuming
more memory and disk space), but does not change anything apart from it.
One pro of preserving existing behavior, pointed by jvillard:
- Suppose some check is experimental or disabled in the config. The
users expect the issue to be found, but it does not show up. They run
`infer --debug` to understand the behavior, and suddenly the issue shows
up.
I, hovewer, find this pro not important enough and potentially confusing
the users even more.
(If they want to investigate seriously, they can always use
--no-filtering, and there are a lot of cases when the issue does not
show up for others, much hard to undertand reasons, than the fact that
it is disabled).
Reviewed By: jvillard
Differential Revision: D17113750
fbshipit-source-id: 46cc93503
Summary:
The default values of config options can sometimes depend on build-time
configuration values. This makes checking that the manuals "remain the same"
trickier as the manuals can be different depending on the platform. This
removes *all* default values from the checked-in manuals. We could be more
fine-grained and scrub only the values that are susceptible to change but for
now this is probably good enough.
This is done by implementing new options `--help-scrubbed` and
`--help-scrubbed-full` and using these in our tests instead of `--help` and
`--help-full` (which remain unaffected).
Also don't wrap the default values in `$(i,...)` anymore because the defaults
can trigger line breaks and then the man page is ill-formatted because that
format is stupid.
Reviewed By: mityal
Differential Revision: D16543779
fbshipit-source-id: bc929ff8c
Summary:
- Add allocation costs to `costs-report.json` and enable diffing over allocation costs.
- Also, let's be more consistent and modular in naming our cost issues.
- introduce a generic issue type `X_TIME_COMPLEXITY_INCREASE` where `X` can be one of the cost kinds. If the function is on the cold start, issue can have the `COLD_START` suffix. Similarly for infinite/zero/expensive calls.
- Change `PERFORMANCE_VARIATION` -> `EXECUTION_TIME_COMPLEXITY_INCREASE`
- Add new issue type for `ALLOCATION_COMPLEXITY_INCREASE_COLD_START` which will be enabled by default
- Refactor cost issues to be more modular and succinct. This also makes addition of a new cost kind very easy by adding the kind into the `enabled_cost_kinds` list in `CostKind.ml`
Reviewed By: mbouaziz
Differential Revision: D15822681
fbshipit-source-id: cf89ece59
Summary:
This is a simple checker that identifies inefficient uses of `keySet` iterator where (not only the key but also) the value is accessed via `get(key)`. It is more efficient to use `entrySet` iterator which already returns both key-value pairs. This optimization would get rid of many extra lookups which can be expensive.
We simply traverse the CFG starting from the loop head upwards and pick up the map that is iterated over. Then, we check in the loop nodes if there is a call to `get(...)` over this map. If, so we report.
Reviewed By: ngorogiannis
Differential Revision: D15737779
fbshipit-source-id: 702465b4e
Summary: Previously there was no way of getting that list from the manual.
Reviewed By: jeremydubreil
Differential Revision: D15158598
fbshipit-source-id: 1705ed59d
Summary:
Keep `--analyzer` around for now for integrations that depend on it.
Also deprecate the `--infer-blacklist-path-regex`,
`--checkers-blacklist-path-regex`, etc. in favour of
`--report-blacklist-path-regex` which more accurately represents what these do
as of now.
Rely on the current subcommand instead of the analyzer where needed, as most of
the code already does.
Reviewed By: jeremydubreil
Differential Revision: D9942809
fbshipit-source-id: 9380e6036
Summary:
This allows infer devs to see the effects their changes have on the infer manuals.
Check in the manuals for each subcommand + the output of `--help-full` to get a
complete picture. If this is too annoying we can also check in only
`--help-full`.
Reviewed By: mbouaziz
Differential Revision: D9916404
fbshipit-source-id: b981e2c33