Summary:
This changes how we select amongst our (currently) 4 Buck integrations
for Java and clang, as well as how the user's choice is reflected by the
Config module.
The old command line interface is still supported but is now deprecated.
The changes in how to select each integration are:
- clang via "flavors", activated with `--flavors`, now with `--buck-clang`
- clang via "compilation DB", activated with `--buck-compilation-database`, unchanged
- Java via "genrule", activated with `--genrule-master-mode`, now with `--buck-java`
- Java "without genrules", used to be activated by *not specifying any other Buck mode*, unchanged
Instead of various `Config` flags corresponding to the previous CLI that
are allowed in any combination of `flavors`,
`buck_compilation_database`, `genrule_master_mode`, `Config` now exposes
a single `buck_mode` datatype. This allows, eg, `flavors` to override
`buck_compilation_database` if needed. It will also make it easier to
get rid of the old "Java without genrules" integration in a later diff
(see inline comments).
Reviewed By: ngorogiannis
Differential Revision: D19175686
fbshipit-source-id: 29b3831be
Summary:
Describe what the --report-*-* options actually do instead of their
outdated documentation from the time where this was
`--checkers-blacklist-regex`, `--infer-blacklist-regex` and the like.
Reviewed By: dulmarod, mityal
Differential Revision: D17906015
fbshipit-source-id: 204349e9e
Summary:
Sqlite versions set their own default page and cache size. Old versions use crazy-non-optimal settings.
Allow setting both from command line and set up reasonable defaults. See, e.g.,
https://wiki.mozilla.org/Performance/Avoid_SQLite_In_Your_Next_Firefox_Feature
for page size notes.
The defaults will cost a maximum of 64Mb in cache per Infer process. These improve merging times significantly.
Reviewed By: jvillard
Differential Revision: D17364643
fbshipit-source-id: b9abab10f
Summary:
I found it very confusing that running infer with --debug makes the
report to be different.
Intuitively, I expect (and I think majority of users would expect) that
`--debug` makes things more verbose (and potentially more slow / consuming
more memory and disk space), but does not change anything apart from it.
One pro of preserving existing behavior, pointed by jvillard:
- Suppose some check is experimental or disabled in the config. The
users expect the issue to be found, but it does not show up. They run
`infer --debug` to understand the behavior, and suddenly the issue shows
up.
I, hovewer, find this pro not important enough and potentially confusing
the users even more.
(If they want to investigate seriously, they can always use
--no-filtering, and there are a lot of cases when the issue does not
show up for others, much hard to undertand reasons, than the fact that
it is disabled).
Reviewed By: jvillard
Differential Revision: D17113750
fbshipit-source-id: 46cc93503
Summary:
The default values of config options can sometimes depend on build-time
configuration values. This makes checking that the manuals "remain the same"
trickier as the manuals can be different depending on the platform. This
removes *all* default values from the checked-in manuals. We could be more
fine-grained and scrub only the values that are susceptible to change but for
now this is probably good enough.
This is done by implementing new options `--help-scrubbed` and
`--help-scrubbed-full` and using these in our tests instead of `--help` and
`--help-full` (which remain unaffected).
Also don't wrap the default values in `$(i,...)` anymore because the defaults
can trigger line breaks and then the man page is ill-formatted because that
format is stupid.
Reviewed By: mityal
Differential Revision: D16543779
fbshipit-source-id: bc929ff8c
Summary: This should stop the bleeding until we get a better solution like shared memory + single writer process.
Reviewed By: mbouaziz
Differential Revision: D10868360
fbshipit-source-id: a4d0b064e
Summary:
Sometimes the default timeout of 10s is not enough(!). Make it
configurable while we work on not hitting it anyway.
Reviewed By: da319
Differential Revision: D10083772
fbshipit-source-id: ab949039f
Summary:
Keep `--analyzer` around for now for integrations that depend on it.
Also deprecate the `--infer-blacklist-path-regex`,
`--checkers-blacklist-path-regex`, etc. in favour of
`--report-blacklist-path-regex` which more accurately represents what these do
as of now.
Rely on the current subcommand instead of the analyzer where needed, as most of
the code already does.
Reviewed By: jeremydubreil
Differential Revision: D9942809
fbshipit-source-id: 9380e6036
Summary:
This allows infer devs to see the effects their changes have on the infer manuals.
Check in the manuals for each subcommand + the output of `--help-full` to get a
complete picture. If this is too annoying we can also check in only
`--help-full`.
Reviewed By: mbouaziz
Differential Revision: D9916404
fbshipit-source-id: b981e2c33
Jules Villard
Nikos Gorogiannis
Mitya Lyubarskiy
Ezgi Çiçek
David Lively
Sungkeun Cho