You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
72 lines
2.4 KiB
72 lines
2.4 KiB
3 years ago
|
/*
|
||
|
|
* This file contains some defines for the floppy disk controller.
|
||
|
|
* Various sources. Mostly "IBM Microcomputers: A Programmers
|
||
|
|
* Handbook", Sanches and Canton.
|
||
|
|
*/
|
||
|
|
#ifndef _FDREG_H
|
||
|
|
#define _FDREG_H
|
||
|
|
|
||
|
|
extern int ticks_to_floppy_on(unsigned int nr);
|
||
|
|
extern void floppy_on(unsigned int nr);
|
||
|
|
extern void floppy_off(unsigned int nr);
|
||
|
|
extern void floppy_select(unsigned int nr);
|
||
|
|
extern void floppy_deselect(unsigned int nr);
|
||
|
|
|
||
|
|
/* Fd controller regs. S&C, about page 340 */
|
||
|
|
#define FD_STATUS 0x3f4
|
||
|
|
#define FD_DATA 0x3f5
|
||
|
|
#define FD_DOR 0x3f2 /* Digital Output Register */
|
||
|
|
#define FD_DIR 0x3f7 /* Digital Input Register (read) */
|
||
|
|
#define FD_DCR 0x3f7 /* Diskette Control Register (write)*/
|
||
|
|
|
||
|
|
/* Bits of main status register */
|
||
|
|
#define STATUS_BUSYMASK 0x0F /* drive busy mask */
|
||
|
|
#define STATUS_BUSY 0x10 /* FDC busy */
|
||
|
|
#define STATUS_DMA 0x20 /* 0- DMA mode */
|
||
|
|
#define STATUS_DIR 0x40 /* 0- cpu->fdc */
|
||
|
|
#define STATUS_READY 0x80 /* Data reg ready */
|
||
|
|
|
||
|
|
/* Bits of FD_ST0 */
|
||
|
|
#define ST0_DS 0x03 /* drive select mask */
|
||
|
|
#define ST0_HA 0x04 /* Head (Address) */
|
||
|
|
#define ST0_NR 0x08 /* Not Ready */
|
||
|
|
#define ST0_ECE 0x10 /* Equipment chech error */
|
||
|
|
#define ST0_SE 0x20 /* Seek end */
|
||
|
|
#define ST0_INTR 0xC0 /* Interrupt code mask */
|
||
|
|
|
||
|
|
/* Bits of FD_ST1 */
|
||
|
|
#define ST1_MAM 0x01 /* Missing Address Mark */
|
||
|
|
#define ST1_WP 0x02 /* Write Protect */
|
||
|
|
#define ST1_ND 0x04 /* No Data - unreadable */
|
||
|
|
#define ST1_OR 0x10 /* OverRun */
|
||
|
|
#define ST1_CRC 0x20 /* CRC error in data or addr */
|
||
|
|
#define ST1_EOC 0x80 /* End Of Cylinder */
|
||
|
|
|
||
|
|
/* Bits of FD_ST2 */
|
||
|
|
#define ST2_MAM 0x01 /* Missing Addess Mark (again) */
|
||
|
|
#define ST2_BC 0x02 /* Bad Cylinder */
|
||
|
|
#define ST2_SNS 0x04 /* Scan Not Satisfied */
|
||
|
|
#define ST2_SEH 0x08 /* Scan Equal Hit */
|
||
|
|
#define ST2_WC 0x10 /* Wrong Cylinder */
|
||
|
|
#define ST2_CRC 0x20 /* CRC error in data field */
|
||
|
|
#define ST2_CM 0x40 /* Control Mark = deleted */
|
||
|
|
|
||
|
|
/* Bits of FD_ST3 */
|
||
|
|
#define ST3_HA 0x04 /* Head (Address) */
|
||
|
|
#define ST3_TZ 0x10 /* Track Zero signal (1=track 0) */
|
||
|
|
#define ST3_WP 0x40 /* Write Protect */
|
||
|
|
|
||
|
|
/* Values for FD_COMMAND */
|
||
|
|
#define FD_RECALIBRATE 0x07 /* move to track 0 */
|
||
|
|
#define FD_SEEK 0x0F /* seek track */
|
||
|
|
#define FD_READ 0xE6 /* read with MT, MFM, SKip deleted */
|
||
|
|
#define FD_WRITE 0xC5 /* write with MT, MFM */
|
||
|
|
#define FD_SENSEI 0x08 /* Sense Interrupt Status */
|
||
|
|
#define FD_SPECIFY 0x03 /* specify HUT etc */
|
||
|
|
|
||
|
|
/* DMA commands */
|
||
|
|
#define DMA_READ 0x46
|
||
|
|
#define DMA_WRITE 0x4A
|
||
|
|
|
||
|
|
#endif
|